When HSRP is configured on a network, which two of these items are provided, which are shared between the routers that run HSRP ?() (choose two)
第1题:
HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? ()(Choose two.)
第2题:
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true?()
第3题:
You have configured router R1 with HSRP, using the standard defaults. Which three statements are true of a default HSRP configuration?()
第4题:
Which two statements are true about the configuration of voice VLANs?()
第5题:
When HSRP is configured on a network, which two of these items are provided, which are sharedbetween the routers that run HSRP? ()(Choose two.)
第6题:
When is a first-hop redundancy protocol needed in the distribution layer?()
第7题:
Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
Routers configured for HSRP can belong to multiple groups and multiple VLANs.
Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
All routers configured for HSRP load balancing must be configured with the same priority.
Routers configured for HSRP must belong to only one group per HSRP interface.
第8题:
active
speak
learn
listen
init
standby
第9题:
HSRP provides redundancy and fault tolerance
HSRP allows one router to automatically assume the function of the second router if the second router fails
HSRP allows one router to automatically assume the function of the second router if the second router starts
HSRP provides redundancy and load balancing
第10题:
Oracle Net Manager
Listener Control Utility
Oracle Net Control Utility
Oracle Net Configuration Assistant
第11题:
The Standby hello time is 2 seconds.
Two HSRP groups are configured.
The Standby track interface priority is 10.
The Standby hold time is 10 seconds
The Standby priority is 100.
The Standby delay is 3 seconds.
第12题:
Init
Idle
Active
Standby
Established
Backup
第13题:
Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router?()
第14题:
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1? ()
第15题:
How can an administrator determine if a router has been configured when it is first powered up?()
第16题:
Which three statements are true about EIGRP route summarization?()
第17题:
HSRP has been configured between two Company devices. What kind of message does an HSRP configured router send out every 3 seconds?()
第18题:
Shared single interface
IP Address
TCP-based hello packets
MAC address
第19题:
physical layer issues
no spanning tree loops
use of non-default HSRP timers
failure to set the command standby 35 preempt
第20题:
Retire
Coup
Resign
Send
Hello
第21题:
a shared single interface
the ability to track serial interfaces
UDP-based hello packets
the impact of flapping links if timers are too low
第22题:
The ASP.NET Impersonation setting should be configured to Enabled. Edit the ASP.NET Impersonation setting by specifying the new local user account.
The Windows Authentication setting should be configured to Enabled.
The Forms Authentication setting should be configured to Enabled by using all the default settings.
The ASP.NET State Service should be configured to log on to the new local user account by using the Services console.
第23题:
TCP-based hello packets
the impact of flapping links if timers are too low
a shared single interface
the ability to track serial interfaces
UDP-based hello packets
第24题:
To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
The default priority of a router is zero (0).
The no standby priority command assigns a priority of 100 to the router.
Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.