A network administrator issues the ping 192.168.2.5 command and successfully tests connectivity to a host that has been newly connected to the network. Which protocols were used during the test?()
第1题:
A.ARP
B.CDP
C.DHCP
D.DNS
E.ICMP
第2题:
A.A remote physical layer problem exists.
B.The host NIC is not functioning.
C.TCP/IP has not been correctly installed on the host.
D.A local physical layer problem exists.
第3题:
Which three of the following protocols will be forwarded to a host specified by the ip helper - address interface configuration command if the configuration has not been modified by the ip forward - protocol udp global con figuration command?()
第4题:
Which of the following protocols would be used to test if one host is reachable by another host, by sending echo requests and waiting for echo replies?()
第5题:
A computer is able to ping other devices on the same network but is unable to ping devices onanother network. Which of the following needs to be configured?()
第6题:
A network administrator issues the ping 192.168.2.5 command and successfully tests connectivity to a host that has been newly connected to the network. Which protocols were used during the test? ()
第7题:
An administrator is configuring an LPAR for a NIM installation and is unsure if the 'Ping Test' option within SMS is a required configuration step. Which statement best describes the 'Ping Test' option?()
第8题:
A system administrator has been asked to document the hardware configuration of a system. Which command can be used to assist in this task?()
第9题:
ARP
CDP
DHCP
DNS
ICMP
第10题:
The 'Ping Test' is a recommended step to verify the IP information entered into the RIPL SMS panel.
The 'Ping Test' is a mandatory step required to commit the IP information entered into the RIPL SMS panel.
The 'Ping Test' is an optional step to verify network configuration entered into the RIPL SMS panel on older copper-based networks.
The 'Ping Test' is an optional step to verify network connectivity between client and server, where ICMP traffic is allowed on the connecting network.
第11题:
Verify the configuration of the connected port on the network switch.
Reboot the server.
Install a new NIC on the server.
Verify that network cables are connected.
第12题:
A remote physical layer problem exists.
The host NIC is not functioning.
TCP/IP has not been correctly installed on the host.
A local physical layer problem exists.
第13题:
A.tracert address
B.ping address
C.arp address
D.traceroute address
第14题:
Which command can be used from a PC to verfy the connectivity between host that connect through path?()
第15题:
Users report that they are unable to connect to a server. An administrator confirms that it is unreachable across the network. Other administrators have been working in the server room throughout the day. Which of the following is the NEXT step the administrator should take?()
第16题:
For a technician to test network connectivity to a remote host on a Unix Server which of the following commands should they run?()
第17题:
A Network Engineer is reporting that one of the AIX hosts is generating too much ICMP traffic, which is slowing the network. Which of the following options is the most probable cause?()
第18题:
An administrator issues the command ping 127.0.0.1 from the command line prompt on a PC.If a reply is received, what does this confirm?()
第19题:
In a TCP/IP network, which of the following protocols is involved when a user issues a ping command?()
第20题:
The user cannot access some Internet websites, but can connect to resources inside the local network. The technician successfully uses the ping command to test the user’s connectivity. Which of the following commands can the technician run NEXT to troubleshoot the issue?()
第21题:
BOOTP
TFTP
ARP
DNS
proxy-ARP
FTP
CDP
第22题:
A large FTP job is in process.
A network interface was misconfigured.
The ping command is being used excessively.
A bad network interface card and/or network cable is in use.
第23题:
BOOTP
TFTP
ARP
DNS
proxy - ARP
FTP
第24题:
The PC has connectivity with a local host.
The PC has connectivity with a Layer 3 device.
The PC has a default gateway correctly configured.
The PC has connectivity up to Layer 5 of the OSI model.
The PC has the TCP/IP protocol stack correctly installed.