This command is applied to the core router facing interface.
This command is applied to the customer facing interface.
The 4 is locally significant and identifies the layer 2 circuit.
The 4 must match exactly on the peer router configuration on the remote end.
第1题:
A. The command is used to establish a static route.
B. The default administrative distance is used.
C. The command is used to configure the default route.
D. The subnet mask for the source address is 255.255.255.0
E. The command is used to establish a stub network
第2题:
A.This command should be executed from the global configuration mode
B.The IP address 10.121.16.8 is the local router port used to forward data
C.102 is the remote DLCI that will receive the information
D.This command is required for all Frame Relay configurations
E.The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
第3题:
QoS policies are applied on the switches of a LAN. Which type of command will show the effects of the policy in real time?()
第4题:
Which of the following statements are true concerning the command ip sla monitor responder typetcpconnect ipaddress 10.1.1.1 port 23?(Choose all that apply.)()
第5题:
Which statement about PPPoA configuration is correct?()
第6题:
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command()。
第7题:
The command is used to establish a static route.
The default administrative distance is used.
The command is used to configure the default route.
The subnet mask for the source address is 255.255.255.0
The command is used to establish a stub network
第8题:
This command should be executed from the global configuration mode
The IP address 10.121.16.8 is the local router port used to forward data
102 is the remote DLCI that will receive the information
This command is required for all Frame Relay configurations
The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
第9题:
Apply the area 4 stub command to all routers in the area
On the ABR, use the area 4 stub command with the no - summary keyword
On the ABR, specify a default cost for the area with the area default - cost command
On the ABR, use the default - information originate command to inject a default route into area 4
Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas
第10题:
If the classification policy is based upon the ToS byte, the qos pre-classify command is required because the ToS byte only appears in the inner IP header.
The ToS byte is copied to the outer header by default. Therefore, the qos pre-classify command is not necessary.
With GRE encapsulation, the qos pre-classify command is applied on the tunnel interface. This practice allows for different OoS configurations on each tunnel.
With GRE encapsulation, the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.
With IPsec encapsulation, the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.
第11题:
The command will initiate a probe with a destination IP address of 10.1.1.1
The command is used on the IP SLA responder and the IP SLA source
The command will allow only source address 10.1.1.1 to source probes
The command will initiate a probe with a destination Telnet port
The command is used to make the router a responder
The command will initiate a probe with a source port of 23
第12题:
The default administrative distance is used.
The command is used to establish a static route.
The command is used to configure the router interfaces.
The command is used to establish a stub network.
The subnet mask for the source address is 255.255.255.0
第13题:
The network administrator of the Oregon router adds the following command to the router configuration: ip route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command (Choose two.)()。
A.The command establishes a static route.
B.The command invokes a dynamic routing protocol for 192.168.12.0.
C.Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
D.Traffic for all networks is forwarded to 172.16.12.1.
E.This route is automatically propagated throughout the entire network.
F.Trafficfor network 172.16.12.0 is forwarded to the 192.168.12.0 network.
第14题:
Which two statements or sets of statements are true about the application of the qos pre-classify command?()
第15题:
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?()
第16题:
With the following CLI command output performed on an LNS: show l2tp session L2TP session 1/to-Denver/2 is up Which two statements are correct? ()(Choose two.)
第17题:
The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?()
第18题:
Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? ()(Choose two.)
第19题:
The last policy is the default policy, which allows all traffic.
The order of policies is not important.
New policies are placed at the end of the policy list.
The insert command can be used to change the order.
第20题:
This command was done on the LNS
This command was done on the LAC
The 1 defines the destination number
The 1 defines the session number
第21题:
The command establishes a static route.
The command invokes a dynamic routing protocol for 192.168.12.0.
Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
Traffic for all networks is forwarded to 172.16.12.1.
This route is automatically propagated throughout the entire network.
Trafficfor network 172.16.12.0 is forwarded to the 192.168.12.0 network.
第22题:
This command should be executed from the global configuration mode.
The IP address 10.121.16.8 is the local router port used to forward data.
102 is the remote DLCI that will receive the information.
This command is required for all Frame Relay configurations.
The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
第23题:
The dsl operating-mode auto command is required if the default mode has been changed
The ip mtu 1496 command must be applied on the dialer interface
The encapsulation ppp command is required
The ip mtu 1492 command must be applied on the dialer interface