A corrupted JFS log device
A corrupted boot logical volume
An incorrect rc.boot entry in /etc/inittab file
A problem initializing paging space
第1题:
An administrator installs a new network card in a properly functioning DC. During the Windows boot up process the DC bluescreens. Which of the following is the NEXT step?()
第2题:
During system boot, rootvg fails to vary on, causing an LED code of 0552. What is the most likely cause for rootvg not varying on?()
第3题:
A system was running properly until a reboot. Following the reboot, the system LED displayed cycles between 0223 and 0229. Which of the following procedures should be performed next?()
第4题:
A system administrator boots a server in normal mode, the boot process displays and LED 551 and stops. LED 551 indicates the root volume group is being varied on. All of the following are probable causes of the problem EXCEPT:()
第5题:
During reboot the system hangs with an LED 0554 message that means, "The boot device could not be opened or a read failed." What recovery procedures should be taken?()
第6题:
During reboot the system hangs with LED 0581 that indicates "Configuring TCP/IP." Which recovery procedures should be taken?()
第7题:
The ODM is corrupted.
There is a hardware failure.
The bosboot command failed.
Not enough space is available in the filesystems.
第8题:
Boot in maintenance and use fsck to check hd5.
Boot in maintenance mode, access the rootvg and check the /etc/inittab for corruption.
Boot in maintenance mode, access the rootvg and rebuild the boot image using the bosboot command.
Boot in maintenance mode, access the rootvg and use the bootlist command to create a valid boot list.
第9题:
Apply power and when the SMS menus appear press 5 repeatedly to enter a maintenance boot automatically. The system will present a maintenance shell eventually.
Boot media such as CDROM or Tape is required to boot into maintenance mode. When inserted into the proper device the system automatically boots into maintenance mode when it can not boot into normal mode.
Apply power and the server automatically boots into maintenance mode where you can select your disk to rebuild the boot logical volume.
Boot media such as CDROM or Tape is required and an administrator must select the proper SMS menus to get into maintenance mode.
第10题:
Missing blv
Network problem
Wrong boot table
Corrupted file system
第11题:
Press F8 and boot to Directory Services Restore Mode.
Press F8 and boot to Last Known Good Configuration.
Reboot the server again.
Press F8 and boot to Safe Mode.
第12题:
Press F8 and boot to Directory Services Restore Mode.
Press F8 and boot to Last Known Good Configuration.
Reboot the server again.
Press F8 and boot to Safe Mode.
第13题:
An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system. Which of the following is the MOST probable cause?()
第14题:
During system boot, the system hangs at LED 0C31. What is the first step the system administrator should take to correct the problem?()
第15题:
A system administrator was able to boot a system from the AIX installation CDROM. The migration install was selected, but the process hung at 92% complete. The system administrator then rebooted the system, which subsequently hung at LED 552. Which of the following options is the most probable cause?()
第16题:
During system boot, the boot process hangs at LED 0551. Which of the following is a likely cause()
第17题:
During reboot, the system hangs with an LED 0554 message that means, "The boot device could not be opened or a read failed." Which of the following recovery procedures should be taken ()
第18题:
Check system console connections
Check system network connections
Boot in service mode and change the bootlist
Boot from the AIX installation media and mount rootvg filesystems
第19题:
Boot in maintenance mode and use fsck to check hd5.
Boot in maintenance mode, access the rootvg and check the /etc/inittab for corruption.
Boot in maintenance mode, access the rootvg and rebuild the boot image using the bosboot command.
Boot in maintenance mode, and reset the root password.
第20题:
Boot in maintenance mode, and verify the Ethernet adapter configuration.
Boot in maintenance mode, access the rootvg and check the /etc/inittab for corruption.
Boot in maintenance mode, access the rootvg and rebuild the boot image using the bosboot command.
Boot in maintenance mode after verifying the network connection, access the rootvg and check the /etc/rc.net file.
第21题:
The BIOS is set with the wrong boot order.
The jumpers have not been set on the hard drive.
The hard drive is not compatible with the system board.
The boot.ini file needs to be modified.
第22题:
A corrupted JFS log device
A corrupted boot logical volume
An incorrect rc.boot entry in /etc/inittab file
A problem initializing paging space
第23题:
The bosboot command failed to complete.
The JFS log device is corrupted.
The initttab file is corrupted.
The /dev entries or /etc files are missing.
第24题:
A network problem
corrupted filesystem
corrupted ODM
corrupted /etc/inittab file