SATA
eSATA
Solid state
PATA
第1题:
A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?()
第2题:
A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?()
第3题:
Which of the following are ways to transport SAN traffic?()
第4题:
After a technician installs a new CMOS battery on a motherboard, which of the following will thetechnician have to change? ()
第5题:
Which of the following can be used to achieve the highest transfer rate for an external hard drive?()
第6题:
A technician needs to configure a computer with an external storage drive. Which of the following interfaces would provide the FASTEST throughput?()
第7题:
A technician is upgrading an internal IDE drive in a laptop. Which of the following HDD types is thetechnician MOST likely using?()
第8题:
A technician is booting up a computer but the computer never moves beyond POST. The floppydisk drive light stays lit continuously during the boot process. Which of the following is the MOST likely cause?()
第9题:
The hard drive is not formatted.
The BIOS is corrupted.
The motherboard has faulty capacitors.
The drive cable is backwards
第10题:
Use a jumper from the motherboard where the new drive is going to be installed.
Use a jumper from a hard drive that is no longer functioning.
Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.
The new hard drive must be replaced
第11题:
SATA
eSATA
Solid state
PATA
第12题:
Add Hardware Wizard
Device Manager
Computer Management
Disk Management
第13题:
A user wants to install an external hard drive using the fastest connection available. Which of the following should the technician recommend?()
第14题:
On which of the following hard drive types must Bob, a technician, change the jumper setting to match the motherboard/cabling combination?()
第15题:
In which of the following locations would a technician set the LBA mode for a hard drive?()
第16题:
Which of the following is eliminated when using SATA instead of PATA technology?()
第17题:
A technician is installing a new power supply into a computer. One of the power supply connectors that the technician needs to connect to the motherboard is square and contains 4-pins. This connector is known as which of the following?()
第18题:
Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?()
第19题:
A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem?()
第20题:
The new drive’s jumper is set for master.
The new drive is connected to the secondary bus as a slave drive.
Both drives’ jumpers are set for cable select.
The old drive’s jumper is set for master and the new drive is set for slave.
第21题:
Set the drive up as basic
Format the drive to FAT32
Install a second hard drive
Set the drive as dynamic
第22题:
Firmware version
System date/time
Bus speeds
Jumper settings
第23题:
Windows cannot be booted from a controller card.
The hard drive must have Windows reinstalled because a new controller card was installed.
The SATA controller card was not set as a boot device in the computer BIOS.
The new controller must have the correct jumper settings for Windows mode.
第24题:
Both hard drives have the master jumper in place.
One hard drive is set as master and the other slave.
The hard drive data cable is reversed.
Both hard drives have the cable select jumper in place.