cldump
cllssvcs
clshowres
clstat -o
第1题:
Which of the following commands will display any user defined verification methods?()
第2题:
A site administrator is configuring Command-level access control. Which of the following statements about Command-level access control are true? Command level access control policies: ()
第3题:
An administrator has made several topology and resource group changes on one node in a running cluster.During verification and synchronization, using the "Emulate" option, many errors are reported. Theadministrator decided the best course of action was to roll back the changes. Prior to the changes beingmade, a cluster snapshot was taken. Which of the following actions will roll back the changes with the least disruption?()
第4题:
Following an unsuccessful cluster fallover test, it is determined that the nfsrg1 resource group was the problem causing the cluster to run the config_too_long evetn. The nfsrg1 resource group contains 10 nfs filesystems that are cross-mounted to the other cluster node. Without modify8ing the time until warning parameters,what can be done to enhance NFS fallover performance?()
第5题:
Which of the following commands will display a snapshot of cluster status, including details of current networkstatus and resource group fallover/fallback policies?()
第6题:
Company.com has a two-node HACMP cluster with a single cascading resource group. Node ’A’ is the normal production node, and Node ’B’ is the standby node. One of the first steps in the HACMP test plan is to start the cluster and to verify that al elements for the resource group have been acquired. The administrator who is conducting the HACMP test starts the HACMP daemons on Node ’B’ with the ’smitty clstart" command. The administrator notices that Node ’B’ acquires the elements of the resource group, including a service IP labels,a shared volume group, and an application server that has been started. The expectation was that Node ’B’ would enter the cluster in a standby status, rather than acquiring production resources. What should the administrator do to correct this problem?()
第7题:
cllsattr
clRGinfo
clshowres
cllistres
第8题:
A loss of quorum has occurred on one of the disks in the failed volume group.
Selective fallover caused by an application moves a resource group to a takeover node.
A check is made to ensure at least one complete copy of all data is available in the volume group.
The MISSING_PV=TRUE environment variable has been set causing the volume group to be forced online.
第9题:
instfix -r
oslevel -r
lslpp -L
oslevel -i grep ML
第10题:
The resource group DNP has been configured.
The resource group option CWOF has been enabled.
The resource group option Inactive Takeover is set.
A resource group fallback timer has been configured.
第11题:
cldump
cllssvcs
clshowres
clstat -o
第12题:
clstop
halt -q
shutdown -F
stopsrc -s cluster
第13题:
A new administrator is performing fallover testing on a two-node cluster and is concerned that the cascading resource group belonging to Node ’A’ did not reintegrate properly after the cluster was restarted on Node ’A’. A stable cluster is reported by clstat,and clRGinfo reports the resource group online on Node ’B’. What type of configuration would cause this type of behavior?()
第14题:
Which of the following commands will display the extended attributes of a resource group?()
第15题:
Which of the following commands will display the current technology level of a server()
第16题:
A customer needs to test the failover capabilities of their cluster. Which of the following AIX commands, whenissued from the command line, will simulate a node crash and cause the cluster resource group running onthat server to fail over to another node?()
第17题:
An HACMP setting timer may used to allow:()
第18题:
Perform a synchronization from a node without the changes.
Apply the cluster snapshot on both nodes while the cluster is running.
Restore HACMP Configuration Database from Active Configuration on the node where the changes weremade
Stop the cluster using the option Unmanage Resource Groups and apply the cluster snapshot on thenode where the changes were made
第19题:
RG1 is Online RG2 is Online
RG1 is Online RG2 is Offline
RG1 is Offline RG2 is Online
RG1 is Offline RG2 is Offline
第20题:
The setting or fallback of a cluster custom resource group
The cluster time to stabilize before starting a custom resource group
A priority node time to acquire custom resource group at cluster start
A fallover node time to process custom resource states to be monitored
第21题:
clRGinfo -m
clappmon -v
clshowres -g
lssrc -ls clappmon
第22题:
RG1 is Online RG2 is Online
RG1 is Online RG2 is Offline
RG1 is Offline RG2 is Online
RG1 is Offline RG2 is Offline
第23题:
Increase the number of NFS daemons for increased performance.
Modify the nfsrg1 resource group to use local NFS cross-mounts.
Create a second resource group to manage half the NFS cross-mounts.
Create post events to handle the cross-mounts after fallover processing.
第24题:
rg1 is configured with a delayed fallback timer
Settling time policy has not been configured for rg1
Node1 does not have sufficient resources to support rg1
Node2 is the first in the ’Default Node Priority’ list for resource group rg1