Configure MSDP between RPs.
Redistribute multicast information in your IGP.
Advertise S, G entries using MBGP.
Configure PIM to advertise group information between RPs.
第1题:
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group?()
第2题:
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()
第3题:
In a PIM topology using anycast RP, in which two ways can the RPs share group information? ()
第4题:
In order to configure two routers as anycast RPs, which of these requirements, af a minimum, must besatisfied?()
第5题:
In order to configure two routers as anycast RPs,which of these requirements,at a minimum, must be satisfied?()
第6题:
What are two purposes of the 224.0.1.40 address in Auto-RP?()
第7题:
Configure a non-unique address on the loopback interface for use by the PIM RP.
Configure MSDP with the unique address (router ID) as the local address of the peer.
Configure MSDP with the non-unique address (router ID) as the local address of the peer.
Configure a unique address on the loopback interface, used as the PIM RP.
第8题:
Configured mapping agents listen to this address.
Mapping agents select RP for a group based on highest IP address of all the group's C-RPs.
RP mapping agent advertises complete list of group-to-RP mappings.
All configured PIM-SM routers listen to this address and learn the correct RP to use for each known group.
第9题:
The source must send a PIM Register message to the rendezvous point (RP)
The source must first join the multicast group using IGMP before sending
The source must perform a Request to Send (RTS) and Clear to Send (CTS) handshake with the PIM designated router (DR)
No control plane signaling needs to be performed;the source can simply begin sending on the local subnet
第10题:
PIM - DM
PIM - SM
PIM - RP
CGMP
IGMP snooping
第11题:
The source must send a PIM Register message to the rendezvous point (RP).
The source must first join the multicast group using IGMP before sending.
The source must perform a Request to Send (RTS) and Clear to Send (CTS) handshake with the PIM designated router (DR).
No control plane signaling needs to be performed; the source can simply begin sending on the local subnet.
第12题:
Configure MSDP between RPs.
Redistribute multicast information in your IGP.
Advertise S, G entries using MBGP.
Configure PIM to advertise group information between RPs.
第13题:
In what PIM topology would you use MSDP within a single domain?()
第14题:
Which are correct descriptions and configurations of Anycast RP?()
第15题:
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicast traffic to a group?()
第16题:
Which three statements about anycast RP are true? ()
第17题:
What is the benefit of using Anycast RP via RFC 4610 for IP multicast RP redundancy?()
第18题:
show ip pim rendez-vous
show ip rpf rp mapping
show ip pim rp mapping
show ip pim rp info
show ip pim
第19题:
In Anycast RP, two or more RPs are configured with the same IP address on loopback interfaces.
Anycast RP provides redundancy and load-sharing capabilities.
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip pim rp-address 1.1.1.1
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip rp-address pim 1.1.1.1
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip anycast-rp pim 1.1.1.1
第20题:
STP root status
VTP mode
Negotiation status
Management domain
Configuration revision number
第21题:
IKE
BGP
RSVP
LDP
第22题:
IP PIM RP-address
IP PIM ssm
IP PIM Sparse-mode
IP PIM Passive
第23题:
Improves convergence of the multicast network due to enhanced RPF checks
Simplifies the number of control plane protocols over other RP redundancy methods
Eliminates the use of Protocol Independent Multicast (PIM) in the topology
Increases the administrative distances in Multicast Source Discovery Protocol (MSDP) configuration
第24题:
MSDP is running between anycast RPs
Anycast RP provides redundancy and load-sharing capabilities
Multicast BGP is running between anycast RPs
In anycast RP,two or more RPs are configured with the same multicast IP address on loopback interfaces
In anycast RP,two or more RPs are configured with the same unicast IP address on loopback interfaces