[edit protocols ospf area area-id] area-range 200.200.0.0/16 discard;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 restrict;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 no-summary;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 suppress;
第1题:
A.Apply an import policy to OSPF; this will import the static routes into OSPF
B.Apply an export policy to protocol "static"; this will export the routes to other protocols.
C.Apply an import policy to the forwarding table; this will import the routes, allowing them to be forwarded to OSPF neighbors.
D.Apply an export policy to OSPF; this will export the static routes to your OSPF neighbors.
第2题:
You want to suppress advertisement of all routes within the 200.200.0.0/16 range to your OSPFneighbors in other areas. Which configuration accomplishes this goal?()
第3题:
An OSPF non-backbone area follows external routes to be flooded within the area. These external routes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?()
第4题:
Which configuration causes RIP-learned routes to be advertised to other RIP neighbors?()
第5题:
You are configuring new BGP neighbor and want to view the configuration for the interface ge-0/0/0.42.Which command do you use to achieve this result?()
第6题:
Which two commands are needed to create and apply an export policy that advertises static routes to OSPF neighbors?()
第7题:
You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriate ARB. Which two commands should you use from the [edit] hierarchy level within the JUNOS software configuration mode?()
第8题:
You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriateABR. Which two commands should you use from the [edit] hierarchy level within JUNOS configuration mode?()
第9题:
[edit protocols ospf area area-id] area-range 200.200.0.0/16 discard;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 restrict;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 no-summary;
[edit protocols ospf area area-id] area-range 200.200.0.0/16 suppress;
第10题:
stub area
transit area
border area
not-so-stubby area
第11题:
set protocol rip no-passive
top edit policy-options policy-statement demo set term 1 from protocol rip set term 1 then accept top set protocols rip group internal export demo
set protocols rip advertise in-out
top edit policy-options policy-statement demo set term 1 from active routes set term 1 then accept top set protocols rip group internal export demo
第12题:
[edit protocols bgp group external] user@router# set interfaces ge-0/0/0.42 ?
[edit protocols bgp group external] user@router# edit show interfaces ge-0/0/0.42
[edit protocols bgp group external] user@router# top show interfaces ge-0/0/0.42
[edit protocols bgp group external] user@router# show interfaces ge0/0/0.42
第13题:
An OSPF non-backbone area allows external routes to be flooded within the area. These external routes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of SPF area does this describe?()
第14题:
Your routing table contains four static routes which you need to redistribute to your OSPF peers. Which method would accomplish this?()
第15题:
You want to allow your device to establish OSPF adjacencies with a neighboring device connected tointerface ge-0/0/3.0. Interface ge-0/0/3.0 is a member of the HR zone.Under which configuration hierarchy must you permit OSPF traffic?()
第16题:
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?()
第17题:
You want to suppress advertisement of all routes within the 200.200.0.0/16 range to your OSPF neighbors in other areas. Which configuration accomplishes this goal?()
第18题:
An OSPF non-backbone area allows external routes to be flooded within the area. These externalroutes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?()
第19题:
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?()
第20题:
stub area
transit area
border area
not-so-stubby area
第21题:
stub area
transit area
border area
not-so-stubby area
第22题:
[edit security policies from-zone HR to-zone HR]
[edit security zones functional-zone management protocols]
[edit security zones protocol-zone HR host-inbound-traffic]
[edit security zones security-zone HR host-inbound-traffic protocols]
第23题:
Apply an import policy to OSPF; this will import the static routes into OSPF
Apply an export policy to protocol static; this will export the routes to other protocols.
Apply an import policy to the forwarding table; this will import the routes, allowing them to be forwarded to OSPF neighbors.
Apply an export policy to OSPF; this will export the static routes to your OSPF neighbors.
第24题:
[edit protocols ospf area area-id] area-range200.200.0.0/16 discard;
[edit protocols ospf area area-id] area-range200.200.0.0/16 restrict;
[edit protocols ospf area area-id] area-range200.200.0.0/16 no-summary;
[edit protocols ospf area area-id] area-range200.200.0.0/16 suppress;