niusouti.com

Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link?()A.show interfaces interfaceB.show vlan briC.show interfaces interface switchportD.show interface interface trunkE.show interfaces v

题目
Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link?()

A.show interfaces interface

B.show vlan bri

C.show interfaces interface switchport

D.show interface interface trunk

E.show interfaces vlan

相似考题

1.What must an administrator do in order to successfully configure a VLAN trunk between two switches?()A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.

2.Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?()A.show interfaces interfaceB.show interfaces interface trunkC.show interfaces interface switchportD.show ip interface briefE.show interfaces vlan

3.Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13.An 802.1Q trunk is configured between the two switches.On CAT1，VLAN10 is chosen as native，but on CAT2 the native VLAN is not specified.What will happen in this scenario？（）A、802.1Q giants frames could saturate the link.B、VLAN10 on CAT1 and VLAN1 on CAT2 will send untagged frames.C、A native VLAN mismatch error message will appear.D、VLAN10 on CAT1 and VLAN1 on CAT2 will send tagged frames.

4.Which two commands can be used to verify a trunk link configuration status on a given cisco switch?()A.show interfaces interfaceB.show interfaces trunkC.show interfaces switchportD.show ip interface briefE.show interfaces vlan

参考答案和解析
参考答案：C, D
更多“Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link?() ”相关问题

  • 第1题：

    You are the network administrator tasked with designing a switching solution for the Company  network.  Which of the following statements describing trunk links are INCORRECT？（）

    • A、 The trunk link belongs to a specific VLAN.
    • B、 Multiple trunk links are used to connect multiple end user devices.
    • C、 A trunk link only supports native VLAN.
    • D、 Trunk links use 802.10 to identify a VLAN.
    • E、 The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.

    正确答案:A,B,C,D

  • 第2题：

    Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario?（）

    • A、802.1Q giants frames could saturate the link.
    • B、VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
    • C、A native VLAN mismatch error message will appear.
    • D、VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

    正确答案:C

  • 第3题：

    Two Company switches are connected via a trunk link. In this network， the original frame is  encapsulated and an additional header is added before the frame is carried over a trunk link. At  the receiving end， the header is removed and the frame is forwarded to the assigned VLAN.  This  describes which technology？（）

    • A、 DISL
    • B、 ISL
    • C、 DTP
    • D、 IEEE 802.1Q
    • E、 MPLS
    • F、 None of the other alternatives apply

    正确答案:B

  • 第4题：

    Which two attributes need to match for two switches to become members of the same MST region？  （）

    • A、the table of 4096 elements that map the respective VLAN to STP instance number
    • B、VTP version
    • C、configuration revision number
    • D、native VLAN ID

    正确答案:A,C

  • 第5题：

    Which two commands can be used to verify a trunk link configuration status on a given cisco switch?（）

    • A、show interfaces interface
    • B、show interfaces trunk
    • C、show interfaces switchport
    • D、show ip interface brief
    • E、show interfaces vlan

    正确答案:B,C

  • 第6题：

    Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?（）

    • A、show interfaces interface
    • B、show interfaces interface trunk
    • C、show interfaces interface switchport
    • D、show ip interface brief
    • E、show interfaces vlan

    正确答案:B,C

  • 第7题：

    多选题
    Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link？（）
    A

    show interfaces interface

    B

    show vlan brief

    C

    show interfaces interface switchport

    D

    show interface interface trunk

    E

    show interfaces vlan


    正确答案： E,A
    解析： 暂无解析

  • 第8题：

    多选题
    You are the network administrator tasked with designing a switching solution for the Company  network.  Which of the following statements describing trunk links are INCORRECT？（）
    A

    The trunk link belongs to a specific VLAN.

    B

    Multiple trunk links are used to connect multiple end user devices.

    C

    A trunk link only supports native VLAN.

    D

    Trunk links use 802.10 to identify a VLAN.

    E

    The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.


    正确答案： A,B,C,D
    解析： 暂无解析

  • 第9题：

    单选题
    Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802. 1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario？（）
    A

    802.1Q giants frames could saturate the link

    B

    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames

    C

    A native VLAN mismatch error message will appear

    D

    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.


    正确答案： D
    解析： 暂无解析

  • 第10题：

    多选题
    What must an administrator do in order to successfully configure a VLAN trunk between two switches?（）
    A

    Set each end of the trunk line to IEEE 802.1Q encapsulation.

    B

    Set the same VTP management domain name on both switches.

    C

    Set all ports on the two switched as access ports.

    D

    Configure one of the two switches as a VTP server.

    E

    Connect the two switches using a rollover cable.

    F

    Use a router to forward VTP traffic between the VLANs.


    正确答案： A,D
    解析： 暂无解析

  • 第11题：

    多选题
    There are 2 switches in the Testking LAN, with no routers. Ports 1, 2 & 3 are assigned to VLAN 1 in switch 1 and 2 and ports 4, 5 & 6 are assigned to VLAN 2 in both switches. These two switches are connected together via a trunked link. Which of the conditions below would verify trunk and VLAN operation?（）
    A

    Host 1 on VLAN 1 can ping Host 2 on VLAN 1

    B

    Host 1 on VLAN 1 can ping Host 4 on VLAN 2

    C

    Host 1 on VLAN 1 can not ping Host 2 on VLAN 1

    D

    Host 4 on VLAN 2 can not ping Host 1 on VLAN 1

    E

    Host 4 on VLAN 2 can ping Host 2 on VLAN 2


    正确答案： C,E
    解析： 暂无解析

  • 第12题：

    单选题
    Two Company switches are connected via a trunk link. In this network， the original frame is  encapsulated and an additional header is added before the frame is carried over a trunk link. At  the receiving end， the header is removed and the frame is forwarded to the assigned VLAN.  This  describes which technology？（）
    A

     DISL

    B

     ISL

    C

     DTP

    D

     IEEE 802.1Q

    E

     MPLS

    F

     None of the other alternatives apply


    正确答案： E
    解析： 暂无解析

  • 第13题：

    You need to investigate a VTP problem between two Company switches. The lack of which two  prevents VTP information from propagating between switches？（）

    • A、A root VTP server
    • B、A trunk port
    • C、VTP priority
    • D、VLAN 1
    • E、None of the other alternatives apply

    正确答案:B,D

  • 第14题：

    In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）

    • A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.
    • B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.
    • C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.
    • D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.

    正确答案:B

  • 第15题：

    You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）

    • A、The link is using IEEE 802.1Q protocol
    • B、The link is using IEEE 802.1E protocol
    • C、Spanning tree is disabled
    • D、Not enough information to determine
    • E、The native VLAN information is identical at each end of the link
    • F、The native VLAN information is different at each end of the link

    正确答案:A,F

  • 第16题：

    Two switches are connected through a trunk link.which two commands show that there is a native VLAN mismatch on that link？（）

    • A、show interfaces interface
    • B、show vlan brief
    • C、show interfaces interface switchport
    • D、show interface interface trunk
    • E、show interfaces vlan

    正确答案:C,D

  • 第17题：

    Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802. 1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario？（）

    • A、802.1Q giants frames could saturate the link
    • B、VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames
    • C、A native VLAN mismatch error message will appear
    • D、VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

    正确答案:C

  • 第18题：

    多选题
    Which two commands can be used to verify a trunk link configuration status on a given cisco switch?（）
    A

    show interfaces interface

    B

    show interfaces trunk

    C

    show interfaces switchport

    D

    show ip interface brief

    E

    show interfaces vlan


    正确答案： A,E
    解析： 暂无解析

  • 第19题：

    单选题
    Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）
    A

    The access link needs to be configured in multiple VLANs.

    B

    The link between the switches is configured in the wrong VLAN.

    C

    The link between the switches needs to be configured as a trunk.

    D

    VTP is not configured to carry VLAN information between the switches.

    E

    Switch IP addresses must be configured in order for traffic to be forwarded between the switches


    正确答案： D
    解析： 暂无解析

  • 第20题：

    单选题
    Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13.An 802.1Q trunk is configured between the two switches.On CAT1，VLAN10 is chosen as native，but on CAT2 the native VLAN is not specified.What will happen in this scenario？（）
    A

    802.1Q giants frames could saturate the link.

    B

    VLAN10 on CAT1 and VLAN1 on CAT2 will send untagged frames.

    C

    A native VLAN mismatch error message will appear.

    D

    VLAN10 on CAT1 and VLAN1 on CAT2 will send tagged frames.


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario?（）
    A

    802.1Q giants frames could saturate the link.

    B

    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.

    C

    A native VLAN mismatch error message will appear.

    D

    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.


    正确答案： C
    解析： 暂无解析

  • 第22题：

    多选题
    Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?（）
    A

    show interfaces interface

    B

    show interfaces interface trunk

    C

    show interfaces interface switchport

    D

    show ip interface brief

    E

    show interfaces vlan


    正确答案： A,C
    解析： 暂无解析

  • 第23题：

    多选题
    You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）
    A

    The link is using IEEE 802.1Q protocol

    B

    The link is using IEEE 802.1E protocol

    C

    Spanning tree is disabled

    D

    Not enough information to determine

    E

    The native VLAN information is identical at each end of the link

    F

    The native VLAN information is different at each end of the link


    正确答案： D,C
    解析： 暂无解析

相关内容