A. The Boot IOS Code is Located in the NVRAM.
B. Check NVRAM for boot system Commands.
C. Bypass NVRAM Configurations.
D. Boot the IOS Code Located in ROM.
E. Perform a Password Recovery.
F. Bypass The Code In ROM.
第1题:
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?()
A. The NVRAM is corrupted.
B. The boot system commands were omitted in the configuration.
C. The configuration register setting is incorrect.
D. The upgraded configuration incompatible with the hardware platform.
E. The upgraded IOS incompatible with the hardware.
第2题:
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
第3题:
A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?()
第4题:
What information does the help topic command provide?()
第5题:
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?()
第6题:
A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file. Which command will display this information, and what is the configuration register value that should be displayed?()
第7题:
第8题:
It checks the configuration register.
It attempts to boot from a TFTP server.
It loads the first image file in flash memory.
It inspects the configuration file in NVRAM for boot instructions.
第9题:
router’s version and serial number to help open a case with JTAC
software documentation describing features and configuration tasks within JUNOS
a brief description of commands and their default values
a verification of the current configuration on the router
第10题:
It checks the configuration register
It attempts to boot from a TFTP server
It loads the first image file in flash memory
It inspects the configuration file in NVRAM for boot instructions
第11题:
RP
multicast source
IGMP router
multicast receiver
PIM designated router
第12题:
The Boot IOS Code is Located in the NVRAM.
Check NVRAM for boot system Commands.
Bypass NVRAM Configurations.
Boot the IOS Code Located in ROM.
Perform a Password Recovery.
Bypass The Code In ROM.
第13题:
A. The IOS image will be ignored.
B. The router will prompt to enter initial configuration mode.
C. The router will boot to ROM.
D. Any configuration entries in NVRAM will be ignored.
E. The configuration in flash memory will be booted.
第14题:
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?()
第15题:
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?()
第16题:
In PIM-SM operations,to which device does the first router that connects with the multicast source sendthe register message?()
第17题:
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next?()
第18题:
An authentication request for a PPP over ATM client has been returned to the router with an address of 255.255.255.254. What does this indicate to the router?()
第19题:
A static IP address is used.
An unnumbered address is used.
The returned RADIUS address is used.
The IP address-pool configuration is used.
第20题:
FTP
SNMPv2
TFTP
KTTPS
第21题:
0x2100
0x2101
0x2102
0x2124
0x2142
第22题:
It checks the configuration register
It attempts to boot from a TFTP server
It loads the first image file in flash memory
It inspects the configuration file in NVRAM for boot instructions
第23题:
The IOS image will be ignored.
The router will prompt to enter initial configuration mode.
The router will boot to ROM.
Any configuration entries in NVRAM will be ignored.
The configuration in flash memory will be booted.
第24题:
The network administrator faled to save the configuration.
The configuration register is set to 0x2100.
The boot system flash command is missing from the configuration.
The configuraiton register is set to 0x2102.
The router is configured with the boot system startup command.