A. The router will not accept connections from the peer.
B. BGP can exchange routing information in this state.
C. The router is listening on its server port for connection requests from the peer.
D. The router ha s sent out an active TCP connection request to the peer.
第1题:
A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
D. The BGP session to the 10.3.3.3 neighbor is established.
E. The BGP session to the 10.2.2.2 neighbor is established.
F. The BGP session to the 10.1.1.1 neighbor is established.
第2题:
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?()
第3题:
Which of the following data structures exist on a router for the OSPF routing protocol?()
第4题:
Which of the following describes the roles of devices in a WAN?()
第5题:
Which of the following statements best describes a Pre-sales Solution Assurance Review?()
第6题:
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?() B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
第7题:
TK1# show ip ospf interface
TK1# show ip ospf priority
TK1# show ospf neighbor detail
TK1# show ospf processes
TK1# show ospf neighbor state
第8题:
clear ip bgp *
clear ip bgp 1.1.1.1
clear ip bgp * soft
clear ip bgp 1.1.1.1 out
第9题:
This router has set the Weight of this route to 10.
This router's BGP table lists this route as an iBGP route.
This router's MED has been set to 10.
This router's BGP table lists an AS_Path length of 10 for this route.
第10题:
R1 has a neighbor 1.1.1.1 command configured.
R1 has a neighbor 2.2.2.2 command configured.
The show ip bgp command lists a line for 190.1.0.0/16 with both an > and an i on the left.
R1 is in ASN 1.
第11题:
It is applied only on the input interface of a router.
It is applied only on the output interface of a router.
It can be configured either on the input or output interface of a router.
It cannot be configured on a router interface.
It is configured under any routing protocol process.
第12题:
It is a teaching guide
It is a blueprint to be strictly followed
It takes into account syllabus and students
It describes in advance what and how to teach
第13题:
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?()
第14题:
Which of these statements accurately identifies how Unicast Reverse Path Forwarding can be employed to prevent the use of malformed or forged IP sources addresses?()
第15题:
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?()
第16题:
The OSPF Hello protocol performs which of the following tasks (Choose two.)()。
第17题:
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?() BGP router identifier 11.11.11.11, local AS number 11 ... Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle (Admin) 2.2.2.2 4 3 173 183 41 0 0 00:58:47
第18题:
config
clientqos.cnf
startup-config
running-configuration
第19题:
OSPF topology table
OSPF interface table
OSPF routing information base
OSPF link-state database
OSPF adjacency table
OSPF neighbor table
第20题:
The output describes the contents of a Type 5 LSA
3.3.3.3 identifies a ro uter as being the router performing redistribution
R1's metric for its best route to reach the router with RID 9.9.9.9 is 100
The router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
第21题:
Idle
Opensent
Active
Established
第22题:
Dissipate heat
Trap foreign matter
Separate air from the oil
All of the above
第23题:
network 10.0.0.0
network 10.10.0.0 mask 255.255.0.0
network 10.10.10.1 mask 255.255.255.255
network 10.10.10.0 mask 255.255.255.0
network 10.0.0.0 mask 255.255.0.0