What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?()A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from act

第1题：

Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover？（）

• A、Switchover ensures that Layer 2 through Layer 4 traffic is not interrupted
• B、Redundancy requires BGP， OSPF， EIGRP， or IS-IS
• C、Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switches
• D、Switchover can be caused by clock synchronization failure between supervisors

第2题：

Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy  using NSF？（）

• A、 independent of SSO
• B、 NSF combined with SSO enables supervisor engine load balancing
• C、 supported by RIPv2， OSPF， IS-IS， and EIGRP
• D、 supports IPv4 and IPv6 multicast
• E、 prevents route flapping
• F、 dependent on FIB tables

第3题：

When applying the configuration in the exhibit and initializing a chassis cluster， which statement is correct？（） [edit chassis] user@host# show cluster { reth-count 3； redundancy-group 1 { node 0 priority 1； node 1 priority 100； } }

• A、Three physical interfaces are redundant.
• B、You must define an additional redundancy group.
• C、node 0 will immediately become primary for redundancy group 1.
• D、You must issue an operational command and reboot the system for the above configuration to take effect.

第4题：

What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）

• A、reset of the primary supervisor
• B、manual switchover from standby to active supervisor
• C、manual switchover from active to standby supervisor
• D、automatic switchover from active to standby on primary supervisor failure

第5题：

As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）

• A、using DHCP snooping
• B、snooping the incoming 802.1Q VLAN tag
• C、using CDP
• D、snooping the CoS marking on the incoming frames

第6题：

What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）

• A、The switch will ignore VTP summary advertisements
• B、The switch will forward VTP summary advertisements
• C、The switch will process VTP summary advertisements
• D、The switch will originate VTP summary advertisements
• E、The switch will create, modify and delete VLANs for the entire VTP domain

第7题：

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）

• A、IEEE 802.10
• B、Misconfigured NIC
• C、User configuration
• D、IEEE 802.1Q
• E、None of the other alternatives apply

第14题：

You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）

• A、 Catalyst 2960 Series
• B、 Catalyst 3750 Series
• C、 Catalyst 4900 Series
• D、 Catalyst 6500 Series

第15题：

What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）

• A、The switch will ignore VTP summary advertisements.
• B、The switch will forward VTP summary advertisements.
• C、The switch will process VTP summary advertisements.
• D、The switch will originate VTP summary advertisements.
• E、The switch will create, modify and delete VLANs for the entire VTP domain.

第16题：

Company has a Catalyst 6500 and you need to configure redundancy between the supervisormodules. With route processor redundancy （RPR+）， the redundant supervisor engine is fullyinitialized and configured， which shortens the switchover time if the active supervisor engine fails.Which three statements are true about the RPR + operations when the redundant supervisorengine switched over the failed primary supervisor engine？（）

• A、Static IP routes are maintained across a switchover because they are configured from entries inthe configuration file
• B、Information about dynamic routing states， maintained on the active supervisor engine， issynchronized to the redundant supervisor engine and is transferred during the switchover
• C、Information about dynamic routing states， maintained on the active supervisor engine， is notsynchronized to the redundant supervisor engine and is lost on switchover
• D、The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routedtraffic is interrupted until route tables reconverge
• E、Static IP routes are cleared across a switchover and recreated from entries in the configurationfile on the redundant supervisor engine
• F、The Forwarding Information Base （FIB） tables are maintained during the switchover. As aresult， routed traffic continues without any interruption when the failover occurs

第17题：

How many access points will a Cisco 7600 Series Router with six installed Cisco Catalyst 6500Series Wireless Services Modules support？（）

• A、300
• B、448
• C、664
• D、1800
• E、2400

第18题：

第19题：

第20题：

第21题：

第22题：

第23题：