进入接口配置模式,使用bandwidth命令设置接口带宽。Router(config-if)#bandwridth 2500000表示设置接口带宽为( )。
A) 2.5Mbps
B) 2.5Gbps
C) 25Gbps
D) 25Mbps
第1题:
进入接口配置模式,使用bandwidth命令设置接口带宽。Router(config-if)#bandwidth 2500000表示设置接口带宽为______。
A.2.5Mbps
B.25Mbps
C.2.5Gbps
D.25Gbps
第2题:
进入接口配置模式,使用band width命令设置接口带宽。Router(config-if) # bandwidth 2500000表示设置接口带宽为( )。
A.2.5Mbit/s
B.25Mbit/s
C.2.5Gbit/s
D.25Gbit/s
第3题:
2、【STCS_03_2】给接口配置PPP协议的命令:
A.Router(config)#encapsulation ppp
B.Router(config-if)#encapsulation ppp
C.Router(config-if)#encapsulation pap
D.Router(config-if)#encapsulation ppp pap
第4题:
【说明】
图5-1是某公司利用Internet建立的VPN
【问题1】(4分)
使用VPN技术,是为了保证内部数据通过Internet安全传输,VPN技术主要采用哪些技术来保证数据安全
【问题2】(3分)
分部1采用DDN通过一台路由器接入Internet。 阅读下面的路由配置信息,将(1)~(3)处标识的语句进行解释。
Router>en (进入特权模式)
Router config terminal (进入全局配置模式)
Router(config)enable secret cisco (设置特权口令)
Router(config)line vty 04
Router(config-line)password goodbad ___(1)___
Router(config-line)exit
Router(config) interface eth 0/0 (进入以太网接口配置模式)
Router(config-if) ip address 202.117.1.1 255.255.255.0 (设置IP地址和掩码)
Router(config-if)no shutdown (启用以太网接口)
Router(config-if)exit
Router(confi9)interface serialO/O (进入串口配置模式)
RouteI<config-if)ip address 211.175.132.10 255.255.255.252 (设置IP地址和掩码)
Router(config-if) bandwidth 256 (指定带宽为256k)
Router(config-if) encapsulation PPP ___(2)___
Router(config-if) no cdpenable ___(3)___
Router(config-if) no shutdown (启用serial接口)
Router(config-if) exit
Router(config)
【问题3】(4分)
分部1的路由器配置为ethernet0/0端口接内部网络,serialO/O端口接外部网络。下列配置指定内外网端口,完成下列配置,将答案填写在答题纸相应的位置。
Router(config-if) inter ethO/O
Router(config-if) ___(4)___
Router(config-if) inter serial0/0
Router(config-if) ___(5)___
Router(config-if) exit
Router(config-if)
【问题4】(4分)
以下是指定VPN在建立连接时协商IKE使用的策略,阅读下面的配置信息,解释(6)、(7)处的命令,将答案填写在答题纸相应的位置。
Router(config-if) crypto isakmp policy 10 (定义策略为10)
Router(config-isakmp) hash md5___(6)___
Router(config-imp) authentication pre-share___(7)___
Router(config-isakmp) exit
Router(config)crypto isakmp keycisc0 123 address 0.0.0.00.0.0.0 (配置预共享密钥为cisco123,对等端为所有IP)
第5题:
在NAT配置过程中需要将端口f0配置成内网接口,将接口f1配置成外网接口,下列配置正确的是:
A.Router(config)#interface fastethernet 0 Router(config-if)#ip nat outside
B.Router(config)#interface fastethernet 1 Router(config-if)#ip nat inside
C.Router(config)#interface fastethernet 0 Router(config-if)#ip nat inside
D.Router(config)#interface fastethernet 1 Router(config-if)#ip nat outside