niusouti.com

is a channel' s capacity which directly reflects the data transfer rate of the channel.(67)functions in a NetWare network which is used to define addressing schemes.(68)is a network layer device that suports multiple LAN interfaces and segments LANs into

题目

is a channel' s capacity which directly reflects the data transfer rate of the channel.(67)functions in a NetWare network which is used to define addressing schemes.(68)is a network layer device that suports multiple LAN interfaces and segments LANs into smaller collision and broadcast domains.(69)．is the popular LAN develped under the direction of the IEEE 802.3.(70)is a device which enables digital microcomputers to communicate across analog telephone lines.

A．The volume

B．The bandwidth

C．The noise

D．The delay

相似考题

1.channel本身必然是同时支持读写的,所以不存在单向channel()此题为判断题(对，错)。

2.Which channel is designated for VHF Digital Selective Calling?A.Channel 70B.Channel 06C.Channel 13D.Channel 16

3.要启用LACP并将交换机端口加入端口信道1,可使用下面哪两个命令之一?()A.Switch(config)#interface port-channel1B.Switch(config)#channel-group 1 mode activeC.Switch#interface port-channel 1D.Switch(config-if)#channel-group 1 mode active

4.关于无缓冲和有冲突的channel,下面说法正确的是()A. 无缓冲的channel是默认的缓冲为1的channelB. 无缓冲的channel和有缓冲的channel都是同步的C. 无缓冲的channel和有缓冲的channel都是非同步的D. 无缓冲的channel是同步的，而有缓冲的channel是非同步的

更多“is a channel' s capacity which directly reflects the data transfer rate of the channel ”相关问题

  • 第1题：

    WhatinterfaceiscreatedwhenanFCPortChanneliscreatedonaCiscoUnifiedComputingSystem?()

    A.Aninterface’san-port-channel’inNXOS

    B.Aninterface’port-channel’inNXOS

    C.Aninterface’port-channel’with’modefc’configured

    D.Aninterface’fc-port-channel’inNXOS


    参考答案：A

  • 第2题：

    根据以下的配置，请判断当主接口serial0出故障后，哪一个备份接口最先被启用？（）[Quidway-Serial0]standby interface serial 1 30[Quidway-Serial0]standby interface serial 2 40[Quidway-Serial0]standby logic-channel 3 50[Quidway-Serial0]standby logic-channel 2 35

    A.serial 1

    B.serial 2

    C.logic-channel 2

    D.logic-channel 3


    参考答案：D

  • 第3题：

    哪条命令将开始捆绑两个物理接口来通过 LACP 创建 EtherChannel 组？

    A．channel-group 2 mode auto

    B．interface port-channel 2

    C．channel-group 1 mode desirable

    D．interface range GigabitEthernet 0/4 - 5


    B

  • 第4题：

    WhichportchannelcommandisrecommendedforN1KVonCiscoUCS?()

    A.channel-groupautomodeon

    B.channel-groupautomodeactive

    C.channel-groupautomodeonsub-groupcdp

    D.channel-groupautomodeonsub-groupmanual

    E.channel-groupautomodeonmac-pinning


    参考答案：E

  • 第5题：

    根据以下的配置，请判断当主接口serial0出故障后，哪一个备份接口最先被启用。（）Quidway（config-if-Serial0）backup interfaceserial130Quidway（config-if-Serial0）backup interfaceserial240Quidway（config-if-Serial0）backup logic-channel350Quidway（config-if-Serial0）backup logic-channel235

    A.serial1

    B.serial2

    C.logic-channel2

    D.logic-channel3


    参考答案：A

  • 第6题：

    网络管理员通过使用命令 SW1（config-if-range)# channel-group 1 mode passive 来配置交换机 SW1 和 SW2 之间的 EtherChannel 链路。必须在 SW2 上使用哪个命令来启用此 EtherChannel？（）

    A．SW2(config-if-range)# channel-group 1 mode active

    B．SW2(config-if-range)# channel-group 1 mode desirable

    C．SW2(config-if-range)# channel-group 1 mode auto

    D．SW2(config-if-range)# channel-group 1 mode passive


    SW2(config-if-range)# channel-group 1 mode active

相关内容