niusouti.com

A neighbor _________ me about him. He_________ Percy Buttons was a beggar.()A.said, spokeB.told, saidC.said, talkedD.told, spoke

题目
A neighbor _________ me about him. He_________ Percy Buttons was a beggar.()

A.said, spoke

B.told, said

C.said, talked

D.told, spoke

相似考题

1.—Mark speaks English well, but you??____________ him.—Thank you. .A. speak as badly as B. speak worse thanC. don’t speak so badly as D. speak much better than

2.Which set of configuration commands configures MBGP on the ERX Edge Router?()A. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-selfB. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activateC. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 activeD. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate

3.Which configuration command establishes an EBGP session to a peer in AS 300?()A. neighbor 200.16.1.2 remote-as 300B. bgp-neighbor 200.16.1.2 remote-as 300C. ebgp-neighbor 200.16.1.2 remote-as 300D. neighbor 200.16.1.2 remote-as 300 connection-type ebgp

4.Where's the boy? We can’t ________c找到) him．

更多“A neighbor _________ me about him. He_________ Percy Buttons was a beggar.() ”相关问题

  • 第1题：

    R1 in ASN 1 with loopback1 address 1.1.1.1 needs to be configured with an iBGP connection to R2 with loopback2 IP address 2.2.2.2. The connection should use the loopbacks.Which o f the following commands is required on R1?（）

    A. neighbor 1.1.1.1 remote- as 1

    B. neighbor 2.2.2.2 remote- as 2

    C. neighbor 2.2.2.2 update - source loopback1

    D. neighbor 2.2.2.2 ibgp -multihop 2

    E. neighbor 2.2.2.2 ibgp - mode


    参考答案：C

  • 第2题：

    Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）

    A. router bgp 1

    B. neighbor 2.2.2.2 remote- as 2

    C. neighbor 2.2.2.2 update - source loopback1

    D. neighbor 2.2.2.2 multihop 2


    参考答案：D

  • 第3题：

    Based on the show ip bgp summary output, which two statements are true?()

    A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.

    B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.

    C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.

    D. The BGP session to the 10.3.3.3 neighbor is established.

    E. The BGP session to the 10.2.2.2 neighbor is established.

    F. The BGP session to the 10.1.1.1 neighbor is established.


    参考答案：B, F

  • 第4题：

    The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?（）BGP router identifier 11.11.11.11, local AS number 11...Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/DownState/PfxRcd1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle(Admin)2.2.2.2 4 3 173 183 41 0 0 00:58:47

    A. router bgp 11

    B. neighbor 1.1.1.1 remote- as 11

    C. neighbor 2.2.2.2 prefix - limit 1

    D. neighbor 1.1.1.1 shutdown


    参考答案：A, D

  • 第5题：

    Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

    A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

    B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

    C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

    D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253


    参考答案：A, B, D

  • 第6题：

    —What (happen) to Herry last night? ．

    —He_________ (fall) down and_________ (hurt) his leg．


    正确答案：
    39. happened;fell;hurt

相关内容