Configure a non-unique address on the loopback interface for use by the PIM RP.
Configure MSDP with the unique address (router ID) as the local address of the peer.
Configure MSDP with the non-unique address (router ID) as the local address of the peer.
Configure a unique address on the loopback interface, used as the PIM RP.
第1题:
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
第2题:
What MSDP solution provides the abiltiy to place the same ip RP address on the loopback of two or more routers?
第3题:
Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()
第4题:
In a PIM topology using anycast RP, in which two ways can the RPs share group information? ()
第5题:
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message (knowing that the MSDP router is also configured as an RP for the PIM domain)?()
第6题:
Which two statements are true about the primary address on an interface?()
第7题:
Source-Active Message
PIM Join
PIM Hello
MSDP Register
第8题:
Manually assign rid.
configure local-address.
enable the fxp0 interface.
Assign nonmartian address to lo0.
第9题:
In Anycast RP, two or more RPs are configured with the same IP address on loopback interfaces.
Anycast RP provides redundancy and load-sharing capabilities.
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip pim rp-address 1.1.1.1
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip rp-address pim 1.1.1.1
Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip anycast-rp pim 1.1.1.1
第10题:
It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface.
You use the primary address when you have multiple IP addresses belonging to the same subnet on the same interface.
It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface.
By default, the primary address on an interface is selected as the numerically highest local address configured on the interface.
第11题:
globally scoped address range
239.0.0.X or 239.128.0.X address range
administratively scoped address range that does not overlap with a link-local MAC address
any Class D address range
site-local scoped address range
第12题:
the IP address of the first Fast Ethernet interface
the IP address of the console management interface
the highest IP address among its active interfaces
the lowest IP address among its active interfaces
the priority value until a loopback interface is configured
第13题:
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()
第14题:
In what PIM topology would you use MSDP within a single domain?()
第15题:
Which are correct descriptions and configurations of Anycast RP?()
第16题:
In which two ways can the router ID selection be controlled?()
第17题:
Which three statements about anycast RP are true? ()
第18题:
Which two statements are true about the primary address on an interface? ()
第19题:
Configure a non-unique address on the loopback interface for use by the PIM RP.
Configure MSDP with the unique address (router ID) as the local address of the peer.
Configure MSDP with the non-unique address (router ID) as the local address of the peer.
Configure a unique address on the loopback interface, used as the PIM RP.
第20题:
第21题:
It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface
You use the primary address when you have multiple IP addresses belonging to the same subnet on the same inteface
It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface
By default, the primary address on an interface is selected as the nmerically highest local address configured on the interface
第22题:
When Area 0 is active, the loopback interface must be configured in OSPF for it to be advertised.
When Area 0 is active, the loopback address is automatically advertised into other areas.
When Area 0 is active, the OSPF router-id must match the loopback address for the loopback address to be advertised.
When Area 0 is active, the router-id must be configured for the loopback address to be advertised.
第23题:
Auto-RP
Anycast RP
Bootstrap router
PIM sparse mode
第24题:
Configure MSDP between RPs.
Redistribute multicast information in your IGP.
Advertise S, G entries using MBGP.
Configure PIM to advertise group information between RPs.