问题:单选题Why is SNMPv2 used to monitor the WX platform?()A SNMPv1 is read-only on WX devices.B SNMPv1 is not supported by WX devices.C SNMPv2 supports both 32- and 64-bit counters.D SNMPv2 does put and get commands to WX devices....
查看答案
问题:多选题Which two conditions will cause switch-to-wire to occur? ()(Choose two.)Aloss of powerBQoS congestionCsoftware failure occuredDWX device exceeded its license speedEtraffic does not match application definiton...
问题:多选题Which two queuing methods are supported by outbound QoS?() (Choose two.)Aweighted fair priorityBweighted fair queuingCweighted strict priorityDweighted strict queuing...
问题:多选题Which two functions are performed in Quick Setup?() (Choose two.)Aoperating modeBauto-deploymentCspeed and duplex settingsDregistration server designation...
问题:多选题Which two configurations are made using the QoS Setup Wizard? ()(Choose two.)AAssign applications to traffic classes.BUse ToS/DSCP values for traffic classes.CExclude subnets from QoS management.DSelect dedicated vs. over-subscribed circuits....
问题:单选题What is one way to escape hardware bypass mode?()A Reset the cabling.B Power cycle the device.C Bounce the service tunnels.D Unlock the device from the console....
问题:多选题Which two secure remote access methods are available on the WX platforms?() (Choose two.)ASSLBSSHCTelnetDHTTP...
问题:单选题How do you verify connectivity between the default gateway and a WX device?()A Check the WX device remote interface and verify that the status is up.B From the WX device, ping the default gateway to make sure it is reachable.C In WebView, check the ser...
问题:单选题Which statement is true about compression subnets?()A Compression subnets are turned on by default.B Compression subnets advertise remote routes.C Compression subnets are usually LAN-side subnets.D Compression subnets are usually WAN-side subnets....
问题:多选题What are two instances when a WX device route carves? ()(Choose two.)AIt occurs every 29 hours.BPacket interception mode is enabled.CThe host is unreachable on the local subnet.DThe subnet is unreachable using the advertised router....
问题:多选题What happens when you enable QoS bandwidth detection? ()(Choose two.)ACircuit speed is reduced by 2% for overhead.BWAN speed can be configured to the LAN speed.CBandwidth is adjusted based on minimum and maximum settingsDWAN bandwidth is detected based...
问题:多选题Exchange acceleration is not working. Which three steps should you use to troubleshoot the problem? ()(Choose three.)ADetermine if CIFS acceleration is enabled.BDetermine if TCP Acceleration (AFP) is enabled.CDetermine if Forward Error Correction is en...
问题:多选题Which three types of optimization does the WX 60 device perform when Exchange 2000 and Outlook 2000 are used in the network? ()(Choose three.)AFast Connection SetupBTCP Acceleration (AFP)CNetwork Sequence CachingDAppFlow's MAPI accelerationEMolecular S...
问题:多选题What are three key pre-installation/configuration considerations when deploying a WX device?() (Choose three.)AcablingBcommunity topologyCrequires a license keyDrequires two IP addressesEregistration server designation...
问题:单选题What must be enabled to view the WAN performance reports?()A Monitor WAN WAN ThroughputB Monitor WAN WAN PerformanceC Device Setup Applications MonitoringD Device Setup Advanced WAN Performance Monitor...
问题:多选题Which three ports does a WX device use for control traffic purposes?() (Choose three.)A3577 UDPB3578 UDPC3678 UDPD3577 TCPE3578 TCP...
问题:多选题Which three static objects are cached by the client-side WXC device?() (Choose three.)AXMLBHTMLCJPEGDJavaScriptsECascading Style Sheets...
问题:多选题What are two requirements when using Packet Flow Acceleration? ()(Choose two.)ATraffic needs be compressed.BQuality of service must be enabled.CA service tunnel must exist in at least one direction.DPFA must be enabled on the client-side WX device....