Which switch would STP choose to become the root bridge in the selection process?()A.32768: 11-22-33-44-55-66B.32768: 22-33-44-55-66-77C.32769: 11-22-33-44-55-65D.32769: 22-33-44-55-66-78

第1题：

In the Cisco FabricPath domain， one switch becomes the root for the multidestination tree. Cisco FabricPath switches compare which three parameters to select the root？ （）

• A、 Root priority
• B、 System ID
• C、 Bridge ID
• D、 Switch ID
• E、 Port ID
• F、 Subswitch ID

第2题：

Which two of the following values does STP take into consideration when it elects the root bridge?（）

• A、The BPDU version number
• B、The access layer bridge setting
• C、The Bridge ID
• D、The spanning-tree update number
• E、The bridge priority
• F、The VLAN number

第3题：

Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?（）

• A、Switch3
• B、Switch4
• C、Switch2
• D、Switch1

第4题：

Which three statements about STP timers are true？（）

• A、STP timers values （hello， forward delay， max age） are included in each BPDU.
• B、A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
• C、To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.
• D、If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.
• E、On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.
• F、The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.

第5题：

Which two values are used by Spanning Tree Protocol to elect a root bridge (Choose two.)（）。

• A、amount of RAM
• B、bridge priority
• C、IOS version
• D、IP address
• E、MAC address
• F、speed of the links

第6题：

Which statement is correct about RSTP port roles？（）

• A、The designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.
• B、The disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.
• C、The backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.
• D、The root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.

第7题：

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）

• A、Designated Root Cost
• B、bridge ID priority
• C、max age
• D、bridge ID MAC address
• E、Designated Root Priority
• F、forward delay

第14题：

Why would an administrator change the value of the spanning-tree priority of a switch?（）

• A、in order to optimize the path that frames take from source to destination
• B、to increase the priority so a designated port will become a root port
• C、to increase the BID, so the switch is more likely to become root bridge
• D、in order to allow VLANs to be sent from one switch to another across a single link
• E、to force a given switch to become an STP server

第15题：

Which three options are considered in the spanning-tree decision process？（）

• A、lowest root bridge ID
• B、lowest path cost to root bridge
• C、lowest sender bridge ID
• D、highest port ID
• E、highest root bridge ID
• F、highest path cost to root bridge

第16题：

Which switch would STP choose to become the root bridge in the selection process?（）

• A、32768: 11-22-33-44-55-66
• B、32768: 22-33-44-55-66-77
• C、32769: 11-22-33-44-55-65
• D、32769: 22-33-44-55-66-78

第17题：

A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。

• A、Establish a direct link from the switch to all other switches in the network.
• B、Assign the switch a higher MAC address than the other switches in the network have.
• C、Configure the switch so that it has a lower priority than other switches in the network.
• D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
• E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.

第18题：

Refer to the output shown on switch SW1 below：  VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1.  What command would you enter to reproduce this output？

第19题：

第20题：

第21题：

第22题：

第23题：