A. show mac-address
B. show arp
C. show table
D. show switchport
第1题:
A. Show vlan
B. Show mac-address-table
C. Show vtp status
D. show spanning-tree root
E. show ip interface brief
第2题:
A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?()
第3题:
The network is being flooded with invalid Layer 2 addresses, causing switch CAM tables to befilled and forcing unicast traffic to be transmitted out all switch ports. Which type of Layer 2 attackis being used here?()
第4题:
When comparing and contrasting the similarities and differences between bridges and switches, which of the following are valid statements?()
第5题:
A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?()
第6题:
Which command will show the MAC addresses of stations connected to switch ports?()
第7题:
In a high-availability network, which command, when placed on ports that have connected end stations, will allow you to prevent delays in service for end stations by placing a port in blocking mode?()
第8题:
In which Spanning-Tree states does a switch port learn MAC addresses?()
第9题:
Which CLI command displays the PPPoE customers that are currently connected to the ERX?()
第10题:
the switch with the lowest MAC address
the switch with the higest MAC address
the switch witch the higest IP address
the switch with the lowest IP address
第11题:
Packets are distributed across the ports in the channel based on both the source and destination MAC addresses.
Packets are distributed across the ports in the channel based on both the source and destination IP addresses.
Packets are balanced across the ports in the channel based first on the source MAC address, then on the destination MAC address, then on the IP address.
Packets are distributed across the access ports in the channel based first on the source IP address and then the destination IP addresses.
第12题:
Blocking
Listening
Forwarding
Learning
Relaying
第13题:
A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.
第14题:
Which command displays the IPNCP parameters for all connected PPPoA subscribers?()
第15题:
Which two of the following steps are necessary to configure inter-VLAN routing between multilayer switches?()
第16题:
A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices.What would be the most efficient way to configure MAC-level security on all these ports? ()
第17题:
A Host connected to an NPV switch is not able to see the storage connected to the core switch. Given the output of the show command below, what is the reason of this issue?() switch# show npv status npiv is enabled External Interfaces: =============== InterfacE. fc1/1, VSAN: 1, FCID. 0x000000, StatE. Other Number of External Interfaces: 4
第18题:
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()
第19题:
You need to configure port security on switch R1. Which two statements are true about this technology? ()
第20题:
Which CLI command displays the currently connected PPPoA subscribers?()
第21题:
show mac-address
show arp
show table
show switchport
第22题:
Port security can be configured for ports supporting VoIP.
With port security configured, four MAC addresses are allowed by default.
The network administrator must manually enter the MAC address for each device in order for the switch to allow connectivity.
Withsecurity configured, only one MAC addresses is allowed by default.
Port security cannot be configured for ports supporting VoIP.
第23题:
Bridges are faster than switches because they have fewer ports.
A switch is a multiport bridge.
Bridges and switches learn MAC addresses by examining the source MAC address of each frame received.
A bridge will forward a broadcast but a switch will not.
Bridges and switches increase the size of a collision domain.