niusouti.com

Which dose the frame－relay interface－dlci command configure?()A. remote DLCI on the main interfaceB. local DLCI on the main interfaceC. local DLCI on the subinterfaceD. remote DLCI on the subinterface

题目
Which dose the frame－relay interface－dlci command configure?()

A. remote DLCI on the main interface

B. local DLCI on the main interface

C. local DLCI on the subinterface

D. remote DLCI on the subinterface

相似考题

1.Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type

2.You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()A. Show interface lmiB. Show frame-relay lmiC. Show interface frame-relayD. Debug frame-relay interface.

3.A new frame－relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-typeE. frame-relay pvc

4.A network administrator needs to configure a router for a Frame Relay connection to a non－Cisco router. Which of the following commands will prepare the WAN interface for this connection?()A. Router(config-if)# encapsulation frame-relay q933aB. Router(config-if)# encapsulation frame-relay ansiC. Router(config-if)# encapsulation frame-relay ietfD. Router(config-if)# encapsulation frame-relay islE. None of the above

更多“Which dose the frame－relay interface－dlci command configure?() ”相关问题

  • 第1题：

    which command allows you to verify the encapsulation type (CISCO OR IETF) for a frame relay link?()

    A.show frame-relay map

    B.show frame-relay lmi

    C.show inter serial

    D.show frame-relay pvc


    参考答案：C

  • 第2题：

    Which dose the frame－relay interface－dlinterface－dlcci command configure?()

    A.remote DLCI on the main interface

    B.local DLCI on the main interface

    C.local DLCI on the subinterface

    D.remote DLCI on the subinterface


    参考答案：C

  • 第3题：

    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）

    • A、This command should be executed from the global configuration mode.
    • B、The IP address 10.121.16.8 is the local router port used to forward data.
    • C、102 is the remote DLCI that will receive the information.
    • D、This command is required for all Frame Relay configurations.
    • E、The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC

    正确答案:E

  • 第4题：

    Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）

    • A、Configure a routing process using the command ipv6 router ospf [process-id].
    • B、Add the network statement for the interfaces on which OSPF will run.
    • C、Configure OSPF on the interface that it will run on.
    • D、Use the passive-interface command on the interfaces on which OSPF should not run.
    • E、Enable routing.

    正确答案:C,E

  • 第5题：

    Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type

    正确答案:B

  • 第6题：

    Which two of the following steps are necessary to configure inter-VLAN routing between multilayer switches？（）

    • A、Configure a dynamic routing protocol.
    • B、Configure SVI interfaces with IP addresses and subnet masks.
    • C、Configure switch ports with network addresses.
    • D、Configure switch ports with the autostate exclude command.
    • E、Document the MAC addresses of the switch ports.

    正确答案:A,B

  • 第7题：

    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。

    • A、This command should be executed from the global configuration mode
    • B、The IP address 10.121.16.8 is the local router port used to forward data
    • C、102 is the remote DLCI that will receive the information
    • D、This command is required for all Frame Relay configurations
    • E、The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC

    正确答案:E

  • 第8题：

    A system administrator needs to configure dump devices for the system. Which command would be used to estimate the size required for a dump device？（）

    • A、lsdev
    • B、chdev
    • C、sysdumpdev
    • D、sysdumpstart

    正确答案:C

  • 第9题：

    单选题
    You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy: CONFIGURE RETENTION POLICY TO REDUNDANCY 3; Which statement is true?（）
    A

    The command fails because you cannot configure a redundancy-based retention policy when backup optimization is enabled

    B

    Backup optimization is performed, but RMAN considers the redundancy-based retention policy when it determines which datafiles should be backed up

    C

    Backup optimization is permanently disabled

    D

    Backup optimization is temporarily disabled because a redundancy-based retention policy is specified


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    Which dose the frame-relay interface-dlinterface-dlcci command configure?（）
    A

    remote DLCI on the main interface

    B

    local DLCI on the main interface

    C

    local DLCI on the subinterface

    D

    remote DLCI on the subinterface


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）
    A

    Show interface lmi

    B

    Show frame-relay lmi

    C

    Show interface frame-relay

    D

    Debug frame-relay interface.


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    Which command is used to configure RMAN to perform a compressed backup for every backup executed？（）
    A

     BACKUP AS COMPRESSED BACKUPSET DATABASE

    B

     BACKUP AS COMPRESSED COPY OF DATABASE

    C

     CONFIGURE DEVICE TYPE DISK BACKUP TYPE TO COMPRESSED BACKUPSET

    D

     CONFIGURE DEVICE TYPE DISK BACKUP TYPE COMPRESS 

    E

     BACKUP DATABASE COMPRESS


    正确答案： B
    解析： 暂无解析

  • 第13题：

    Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?()

    A.show frame-relay end-to-end

    B.show frame-relay map

    C.show frame-relay lmi

    D.show frame-relay pvc


    参考答案：B

  • 第14题：

    A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type
    • E、frame-relay pvc

    正确答案:B

  • 第15题：

    Which configuration command dynamically detects and configures a Bridged 1483 interface?（）

    • A、auto-configure ip
    • B、auto-configure ppp
    • C、auto-configure pppoe
    • D、auto-configure bridgedethernet

    正确答案:D

  • 第16题：

    Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?（）

    • A、show frame-relay end-to-end
    • B、show frame-relay map
    • C、show frame-relay lmi
    • D、show frame-relay pvc

    正确答案:B

  • 第17题：

    Which dose the frame-relay interface-dlci command configure?（）

    • A、remote DLCI on the main interface
    • B、local DLCI on the main interface
    • C、local DLCI on the subinterface
    • D、remote DLCI on the subinterface

    正确答案:C

  • 第18题：

    which command allows you to verify the encapsulation type CISCO OR IETF for a frame relay link?（）

    • A、show frame-relay map
    • B、show frame-relay lmi
    • C、show inter serial
    • D、show frame-relay pvc

    正确答案:C

  • 第19题：

    Which command is used to initialize and configure a NIM master？（）

    • A、/usr/sbin/nim_init
    • B、/usr/bin/installnim
    • C、/usr/sbin/nimconfig
    • D、/usr/sbin/setup_server

    正确答案:C

  • 第20题：

    Which command is used to configure RMAN to perform a compressed backup for every backup executed？（）

    • A、 BACKUP AS COMPRESSED BACKUPSET DATABASE
    • B、 BACKUP AS COMPRESSED COPY OF DATABASE
    • C、 CONFIGURE DEVICE TYPE DISK BACKUP TYPE TO COMPRESSED BACKUPSET
    • D、 CONFIGURE DEVICE TYPE DISK BACKUP TYPE COMPRESS 
    • E、 BACKUP DATABASE COMPRESS

    正确答案:C

  • 第21题：

    单选题
    Which configuration command dynamically detects and configures a PPPoA interface?（）
    A

    auto-configure ip

    B

    auto-configure ppp

    C

    auto-configure pppoe

    D

    auto-configure bridgedethernet


    正确答案： C
    解析： 暂无解析

  • 第22题：

    单选题
    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。
    A

    This command should be executed from the global configuration mode

    B

    The IP address 10.121.16.8 is the local router port used to forward data

    C

    102 is the remote DLCI that will receive the information

    D

    This command is required for all Frame Relay configurations

    E

    The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）
    A

    Router(config-if)# encapsulation frame-relay q933a

    B

    Router(config-if)# encapsulation frame-relay ansi

    C

    Router(config-if)# encapsulation frame-relay ietf

    D

    Router(config-if)# encapsulation frame-relay isl

    E

    None of the above


    正确答案： E
    解析： 暂无解析

相关内容