Refer to the exhibit. What is the effect of the OSPF configuration on router B?()A. All interfaces will be in area 0B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0

Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）

A. the routes originating from the RIP routing domain

B. the routes originating from the OSPF stub area

C. all OSPF inter and intra - area routes

D. all routes originating from RIP and OSPF routing domains

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

A. The no auto - summary command needs to be added under router eigrp 1

B. The subnets keyword was not included in the redistribute command under router ospf 1

C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

D. The default - information originate command needs to be added under router ospf 1

E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

A.The router is in area 49.0001.0002

B.The router acts as a Level 1 - 2 router

C.CLNS routing is enable d for the router

D.The router has a system ID of 0003.0004

E.The interfaces have a functional IS - IS configuration

F.The network service access point selector (NSEL) byte has a value of 0

A. RTA will not establish an OSPF adjacency w ith RTB

B. RTA will send OSPF hello packets, but will not send OSPF updates

C. RTA will not accept OSPF hello packets from RTB

D. RTA will send OSPF updates, but will not establish an adjacency with RTB

A.The loopback addresses are on different subnets

B.The value of the dead timers on the router are different

C.Route summarization is enabled on both routers

D.The process indentifier on router A is different than the process identifier on router B

A.No configuration file was found in NVRAM.

B.No configuration file was found in flash.

C.No configuration file was found in the PCMCIA card.

D.Configuration file is normal and will load in 15 seconds.

A.show ip ospf

B.show ip ospf interface

C.show ip ospf neighbor

D.show ip ospf database

E.show ip ospf statistics

F.show running - config begin router ospf

Refer to the exhibit. AS 65500 is not advertising the prefix 192.168.12.0/22 to its provider. AS 65500 is running OSPF as its IGP. Whi ch of the following additions to the configuration is most likely to solve the problem?（）

A. RouterA(config)#ip cef

B. RouterA(config)#ip route 192.168.12.0 255.255.255.252 null 0

C. RouterA(config - router)#ebgp multihop 1

D. RouterA(config - router)#re distribute ospf 1

E. RouterA(config - router)#neighbor 192.168.14.253 next - hop - self

F. RouterA(config - router)#neighbor 192.168.14.253 local - as 65500

Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）

A. Enter the configuration on router B1.

B. Enter the configuration on router B4.

C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.

D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.

E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.

A. the serial 1/1 address

B. the serial 2/0 address

C. a randomly generated internal address

D. the configured router - id address

A. Router RTA is the BDR

B. Router RTA is directly connected to interface 192.168.45.1

C. Neighbor 192.168.45.1 has changed its OSPF priority number

D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs

A. On the ABR router ospf 10 area 3 stub

B. On all Area 3 routers router ospf 10 area 3 stub

C. On all Area 3 routers router ospf 10 area 3 stub no - summary

D. On the ABR router ospf 10 area 3 nssa

E. On the ABR rou ter ospf 10 area 3 stub no - summary

Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）

A.FastEthernet0 /0

B.FastEthernet0 /1

C.Serial0/0

D.Serial0/1.102

E.Serial0/1.103

F.Serial0/1.104