Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?()A. On the ABR router ospf 10 area 3 stubB. On all Area 3 routers router ospf 10 area 3 stubC. On all Area 3 routers router ospf 10 area 3 stu

题目

Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?()

A. On the ABR router ospf 10 area 3 stub

B. On all Area 3 routers router ospf 10 area 3 stub

C. On all Area 3 routers router ospf 10 area 3 stub no - summary

D. On the ABR router ospf 10 area 3 nssa

E. On the ABR rou ter ospf 10 area 3 stub no - summary

相似考题

1.An OSPF non-backbone area allows external routes to be flooded within the area. These externalroutes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?（）A. stub areaB. transit areaC. border areaD. not-so-stubby area

2.ABR R1 has been configured with an area 1 stub no － summary command. Which stubby area type is area 1?()A. StubB. Totally stubbyC. NSSAD. Totally NSSA

3.Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? ()A. area 0 stub o n routers R4 and R5B. area 5 stub on routers R4 and R5C. area 5 stub no - summary on routers R4 and R5D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5E. area 5 stub no - summary on router R4 and area 5 stub on router R5

4.Which configuration command places interfaces whose IP addresses are between 192.168.0.0 and 192.168.255.255 into OSPF area 0?()A.AB.BC.CD.D

更多“Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?() ”相关问题

第1题：

To make OSPF area 4 totally stubby, the following command was issued on the ABR in router configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）
A. Apply the area 4 stub command to all routers in the area
B. On the ABR, use the area 4 stub command with the no - summary keyword
C. On the ABR, specify a default cost for the area with the area default - cost command
D. On the ABR, use the default - information originate command to inject a default route into area 4
E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas

参考答案：A, B
第2题：

You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configuration s are correct for generating type 3 LSAs?（）
A. Internal routers within the backbone area (area 0)
B. Internal routers within the NSSAs
C. Internal routers within the stubby areas
D. ASBRs
E. ABRs
F. DRs and BDRs

参考答案：E
第3题：

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?()

A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

参考答案：A, D
第4题：

You are troubleshooting an OSPF problem where external routes are not showing up in the OSPF database. Which two options a re valid checks that should be performed first to verify proper OSPF operation?（）
- A、Are the ASBRs trying to redistribute the external routes into a totally stubby area?
- B、Are the ABRs configured with stubby areas?
- C、Is the subnets keyword being used with the redistribution command?
- D、Is backbone area (area 0) contiguous?
- E、Is the CPU utilization of the routers high?
正确答案:A,C
第5题：

When implementing OSPFv3, which statement describes the configuration of OSPF areas?（）
- A、In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
- B、In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
- C、In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
- D、In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.
正确答案:C
第6题：

Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
- A、Router(config)#router ospf 1
- B、Router(config)#router ospf 0
- C、Router(config)#router ospf area 0
- D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
- E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
- F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
正确答案:A,D
第7题：

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
- A、Router(config)#router ospf 1
- B、Router(config)#router ospf 0
- C、Router(config)#router ospf area 0
- D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
- E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
- F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
正确答案:A,D
第8题：

单选题
An OSPF non-backbone area allows external routes to be flooded within the area. These externalroutes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?（）
A
stub area
B
transit area
C
border area
D
not-so-stubby area

正确答案： A
解析：暂无解析
第9题：

多选题
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
A
TestKingRouter(config)# router ospf 0
B
TestKingRouter(config)# router ospf 1
C
TestKingRouter(config)# router ospf area 0
D
TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
E
TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
F
TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0

正确答案： A,D
解析：暂无解析
第10题：

多选题
To make OSPF area 4 totally stubby, the following command was issued on the ABR in router configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）
A
Apply the area 4 stub command to all routers in the area
B
On the ABR, use the area 4 stub command with the no - summary keyword
C
On the ABR, specify a default cost for the area with the area default - cost command
D
On the ABR, use the default - information originate command to inject a default route into area 4
E
Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas

正确答案： C,A
解析：暂无解析
第11题：

单选题
Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router？（）
A
A virtual link to area 0.
B
OSPF summarization command.
C
default - cost extension to the area command.
D
no - summary extension to the area stub comm and.
E
None of the other alternatives apply

正确答案： D
解析：暂无解析
第12题：

多选题
You are troubleshooting an OSPF problem where external routes are not showing up in the OSPF database. Which two options a re valid checks that should be performed first to verify proper OSPF operation?（）
A
Are the ASBRs trying to redistribute the external routes into a totally stubby area?
B
Are the ABRs configured with stubby areas?
C
Is the subnets keyword being used with the redistribution command?
D
Is backbone area (area 0) contiguous?
E
Is the CPU utilization of the routers high?

正确答案： A,B
解析：暂无解析
第13题：

Refer to the exhibit. What is the effect of the OSPF configuration on router B?()

A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2

参考答案：D
第14题：

Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router?()

A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply

参考答案：D
第15题：

Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router？（）
- A、A virtual link to area 0.
- B、OSPF summarization command.
- C、default - cost extension to the area command.
- D、no - summary extension to the area stub comm and.
- E、None of the other alternatives apply
正确答案:D
第16题：

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
- A、TestKingRouter(config)# router ospf 0
- B、TestKingRouter(config)# router ospf 1
- C、TestKingRouter(config)# router ospf area 0
- D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
- E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
- F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
正确答案:B,E
第17题：

Which OSPF area type allows for the flooding of a Type 7 LSA?（）
- A、stub
- B、transit
- C、border
- D、not-so-stubby
正确答案:D
第18题：

You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configuration s are correct for generating type 3 LSAs?（）
- A、Internal routers within the backbone area (area 0)
- B、Internal routers within the NSSAs
- C、Internal routers within the stubby areas
- D、ASBRs
- E、ABRs
- F、DRs and BDRs
正确答案:E
第19题：

An OSPF non-backbone area allows external routes to be flooded within the area. These externalroutes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?（）
- A、stub area
- B、transit area
- C、border area
- D、not-so-stubby area
正确答案:D
第20题：

单选题
ABR R1 has been configured with an area 1 stub no - summary command. Which stubby area type is area 1?（）
A
Stub
B
Totally stubby
C
NSSA
D
Totally NSSA

正确答案： D
解析：暂无解析
第21题：

单选题
You are developing a verification plan for an upcoming OSPF implementation. Part of this plan is to verify the status of type 3 LSAs within the network. Which routers should you verify first to ensure that the configuration s are correct for generating type 3 LSAs?（）
A
Internal routers within the backbone area (area 0)
B
Internal routers within the NSSAs
C
Internal routers within the stubby areas
D
ASBRs
E
ABRs
F
DRs and BDRs

正确答案： D
解析：暂无解析
第22题：

单选题
Which OSPF area type allows for the flooding of a Type 7 LSA?（）
A
stub
B
transit
C
border
D
not-so-stubby

正确答案： D
解析：暂无解析
第23题：

多选题
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）
A
Router（config）#router ospf 1
B
Router（config）#router ospf 0
C
Router（config）#router ospf area 0
D
Router（config-router）#network 192.168.16.0 0.0.0.255 area 0
E
Router（config-router）#network 192.168.16.0 0.0.0.255 0
F
Router（config-router）#network 192.168.16.0 255.255.255.0 area 0

正确答案： B,C
解析：暂无解析

niusouti.com

Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?()A. On the ABR router ospf 10 area 3 stubB. On all Area 3 routers router ospf 10 area 3 stubC. On all Area 3 routers router ospf 10 area 3 stu

题目

相似考题

更多“Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?() ”相关问题

相关内容